Your cart is empty.
Your cart is empty.1/2 inch x 1/2 inch male iron pipe, lead free, straight connector, Shark Bite push fit fittings for use with copper tubing cts, cpvc & PEX with integral tube liner included, constructed of ds brass, certified to 200 psi & 200 degrees Fahrenheit, design certified to asset 1061/Nsf61 standards, meets upc, ipc & cupc requirements, fitting are listed with iapmo & are certified for use on potable & hydronic water distribution, certified for underground applications & as a manufactured joint without the need for access panels, lead free Compliant to federal law 111-380, bagged.
Gerard Laferriere
Reviewed in Canada on March 12, 2025
parfait
Justin B. Helms
Reviewed in the United States on February 14, 2025
Durable, works as advertised.
Carolyn Deforest
Reviewed in Canada on February 22, 2024
Great Amazon offers for their taps
Eduardo Valdez
Reviewed in Mexico on October 24, 2024
Es de muy fácil instalación y sella muy bien. Justo para cuando hay alguna emergencia.
Ciclomantis
Reviewed in Mexico on June 26, 2023
Muy buen conector, perfecto para direccional flujo de agua él distintas direcciones. Y muy fácil de instalar así mismo de quitar. Muy recomendable en jardinería
neilth
Reviewed in the United States on May 26, 2023
I used these fittings to add several sprinkler heads to my sprinkler system and found that mysteriously the new heads would not spray any water. I finally discovered that the water filters under the sprinkler heads were interfering with the water exiting the Sharkbite fittings. Once I added riser extensions, raising the sprinkler heads and their filters, my problem was resolved and everything is now working perfectly.
Kurtis Bryden
Reviewed in Canada on May 16, 2022
Had to make a quick repair and these came in handy.
Art
Reviewed in Canada on February 14, 2021
Just as described...clean treads an perfect fit
Reality Check
Reviewed in the United States on June 25, 2020
I had to change out a tub valve through a tiny 7 inch round opening . This fitting had 4 pipes: A hot and cold PEX, a PEX running to the shower, and a hard copper line running to the tub spout. All fittings were iron pipe thread into the valve. The PEX fittings will slip and rotate (with some difficulty) so I was able to unscrew them, and I was barely able to fit a mini tubing cutter around the copper to cut it. That's where this SharkBite fitting came in. With a bit of delicate attention to the end of the copper to make sure that it wasn't sharp, this fitting slid right over the copper and allowed me to tighten it into the valve body. Everything lined up like before and nothing leaked. This took all day, but that was due to the tiny opening that i had to work through. This SharkBite was the easiest to install (30 seconds) and everything is just as rigid as before. Well worth the money.My only concern was that there was a bit of solder on the pipe that I delicately filed off. After that I polished it off with 600 grit sandpaper to eliminate any possible remaining file marks. If there had been a solder bump or file groove, it is quite possible that would have resulted in a leak, since the sealing location point is to the outside of the pipe.In the end all worked out well, and I am satisfied.
Blashawk
Reviewed in Canada on August 8, 2019
It made my plumbing work so easy. So happy surprised how easy it is. I had to connect 2 copper tubings between the wall. It was so easy. Just push here; and just push there ;and the work was done. No leaks, No nothing. Just as advertised.
Fernand Valliere
Reviewed in Canada on December 22, 2019
Not used yet but seem too be of good quality
SDB
Reviewed in Canada on April 14, 2019
Sharkbite fitting, what more can I say?
Recommended Products
